|
|
| Shopping
Cart: |
|
0
Items
In Cart |
| Total:
$0.00
|
|
 |
|
|
 |
| |
| |
| |
| |
| |
| |
| |
| |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
EPDM LC-60 Bonding Adhesive, Solvent Based (5G)
|
| EPDM-302036-1 |
$180.00 SALE $145.95 |
| (Savings: $34.05) |
|
| |
|
|
|
Buy
10
or more and pay $141.95 each (save $38.05)
|
|
|
| |
|
|
|
|
| |
| |
| |
PRODUCT: #LC-60 EPDM LIQUID
BONDING ADHESIVE BY WEATHERBOND. FOR EPDM ROOFING. 5-GALLON CAN. PRICE/CAN.
Flammable item. UPS Ground or truck Shipment ONLY. High VOC -- Cannot ship to VOC restricted areas.
DESCRIPTION:
WeatherBond LC-60 Bonding Adhesive is a high-strength solvent-based contact adhesive that allows quick bonding of EPDM membrane to various substrates (see datasheet).
It is a synthetic rubber adhesive formulated specifically for application with a 1/2" (13 mm) medium nap roller with enough versatility in the tack time of the film to allow large areas to be coated and adhered at one time.
LC-60 Bonding Adhesive is designed for bonding WeatherBond EPDM Membranes,
Carlisle EPDM membrane, Versico EPDM membranes, and all other EPDM, Butyl and Epichlorohydrin membranes to various substrates. Its also suitable to adhere TPO membranes. This product is also called Carlisle SURE-SEAL 90-8-30A.
COVERAGE RATES:
About 60 square feet
(56 sq m) per gallon (finished surfaces).
Porous and irregular
surfaces and substrates may require more bonding adhesive than the typical
coverage rate.
CAUTIONS:
1. Read the Material Safety Data Sheet for complete safety information
prior to use.
2. WeatherBond
LC-60 Bonding Adhesive is EXTREMELY FLAMMABLE - It contains solvents that
are dangerous fire and explosion hazards when exposed to heat, flame or
sparks. Store and use away from all sources of heat, flame or sparks. Do
not smoke while applying. Do not use in a confined or unventilated area.
Vapors are heavier than air and may travel along ground to a distant
ignition source and flash back. A red caution label is required when
shipping.
3. Avoid breathing
vapors. Keep container closed when not in use. Use with adequate
ventilation. If inhaled, remove to fresh air. If not breathing, perform
artificial respiration. If breathing is difficult, give oxygen. Call a
physician immediately. During application, efforts must be made to prevent
fumes from entering the building via air ventilation ducts. Do not place
open containers or mix adhesive near fresh air intake units. When
possible, shut down or seal off the closest units.
4. If swallowed, DO
NOT INDUCE VOMITING. Call a physician immediately.
5. Avoid contact
with eyes. Safety glasses or goggles are recommended. If splashed in eyes,
immediately flush eyes with plenty of clean water for at least 15 minutes.
Contact a physician immediately.
6. Avoid contact
with skin. Wash hands thoroughly after handling. In case of contact with
skin, thoroughly wash affected area with soap and water. Note: Solvent
resistant Hycron gloves are recommended when using this product to protect
hands from irritating ingredients.
7. Do not thin
Bonding Adhesive. Thinning will affect performance. Excessively thick or
gelled material should be discarded.
READ SHEETS BEFORE USE.
PRACTICE YOUR
TECHNIQUE BEFORE USE !
Technical Data Sheet
MSDS Sheet
Questions?
Email us at
sales@bestmaterials.com or
Call us at 1-800-474-7570 or 602-272-8128
You'll get a prompt reply!
similar product terms: SURE-SEAL 90-8-30A, sure-seal adhesive, epdm adhesive, epdm glue, rubber roof glue, roof membrane glue, roof membrane adhesive, roofing membrane adhesive, single ply adhesive, single ply glue, epdm roof adhesive, rv rubber roof adhesive, rv roof adhesive, membrane roof adhesive, epdm rubber roofing adhesive , epdm flat roof adhesive, epdm flat roofing adhesive, single ply roofing adhesive, single ply membrane adhesive, carlisle epdm adhesive, carlisle adhesive, versico epdm adhesive, versico adhesive, jm epdm adhesive |
|
|
|