Best Materials Roofing Supplies


Log-In   Log-Out
 Shopping Cart:
  0   Items  In Cart
 Total: $0.00
   Hardware & LPG  
   Metal Goods  
   Paint Supplies  
   Pipe Flashings  
   Roof Coatings  
   Roof Hatch/Vent  
   Roof Repair  
   Roof Tiles  
   Safety Products  
   Snow Guards  
   Support Systems  
   Tool Accessories  
   Tools & Equip.  
   TPO & PVC  
Shop With

MasterProtect H 400 Concrete/Masonry Silane Sealer (Enviroseal40) (5G) - MasterProtect H 400 (formerly Enviroseal® 40), clear, water-based, 40% silane  penetrating sealer / water repellant. For concrete and masonry. 5-Gallon Pail. Price/Pail. (36 pails/pallet)
MasterProtect H 400 Concrete/Masonry Silane Sealer (Enviroseal40) (5G)
$233.00 SALE $174.95
(Savings: $58.05)
 Buy 10 or more and pay $160.77 each (save 31.00%) 
  Order Options:  
  Add To Cart  
  Add To Saved Cart  
  PRODUCT: MasterProtect H 400 (formerly Enviroseal® 40), clear, water-based, 40% silane penetrating sealer / water repellent. 5-Gallon Pail. Price/Pail. (36 pails/pallet)

FEATURES: MasterProtect H 400 is a clear, water-based, 40% silane  (alkylalkoxysilane) penetrating sealer with traffic bearing qualities.

  • Water based, VOC compliant (Except S. Calif SCAQMD)
  • Excellent penetration
  • High moisture repellant
  • Breathable
  • Transparent, non-staining
  • One component

Provides long-lasting protection against moisture intrusion, freeze/thaw cycles, and chloride intrusion.

Ideal for traffic-bearing surfaces.

YIELD (typical)

Concrete: 100 – 200 ft2/gal (2.4 – 4.8 m2/L)

Brick: 100 – 200 ft2/gal (2.4 – 4.8 m2/L)

Always apply a test area to determine actual coverage rates. Coverage rates will vary greatly with the porosity of the substrate


  • Parking garages
  • Stadiums
  • Bridge decks
  • Concrete highway road surfaces
  • Ramps and barrier rails
  • Stadiums
  • Cooling towers
  • Many other reinforced concrete structures
  • Brick Pavers
  • Unglazed Tile
  • Chimneys
  • Hard Burnt Brick
  • Stucco
  • Horizontal and vertical
  • Exterior or interior
  • Above grade SUBSTRATE
  • Concrete substrates: architectural, glass-fiberreinforced, precast, cast in place, slicia fume
  • New and existing concrete
1. Verify substrate has properly cured. Concrete should obtain 80% of design strength, typically achieved within 14 – 28 days.
2. Clean concrete surfaces of all sand, surface dust and dirt, oil, grease, chemical films and coating,s and other contaminants prior to application. Use waterblast, sandblast, or shotblast as necessary to achieve the desired surface condition.
3. Surface, air, and material temperatures should be 40 to 110° F (4 to 43° C) during application. Do not apply Enviroseal® 40 when temperatures are expected to fall below 40° F (4° C) within 12 hours.
4. Surfaces to be treated can be slightly damp; however, a dry surface is suggested for maximum penetration of sealer. Do not apply Enviroseal® 40 if standing water is visible on the surface to be treated.
5. Crack control, caulking, patching, and expansion joint sealants can be installed before or after application of the sealer.
6. Allow a minimum of 6 – 12 hours curing time for caulking and sealant materials (or until they have skinned over) before applying Enviroseal® 40.



  • Enviroseal  20, 20% silane, for food processing areas and more cost sensitive projects.
  • Enviroseal 7 for hard-burnt vertical brick and other dense surfaces.
  • Envirseal PBT for very porous vertical surfaces, such as split face block and lightweight concrete.  
Email us at or
Call us at 1-800-474-7570 or 602-272-8128
You'll get a prompt reply!
similar product terms: masterprotect, masterprotect h 400, enviroseal-40, environseal, evioseal, eviron-seal, masonry sealer, masonry waterproofing, concrete waterproofing, concrete sealer, concrete sealers, concrete finish, concrete driveway sealer, cement sealer, stamped concrete sealer, wet look concrete sealer, clear concrete sealer, concrete water seal, concrete block sealer, penetrating concrete sealer

  Associated Items:  
Hydrozo 100, 100% Silane Penetrating Sealer (5G)
Hydrozo 100, clear, 100% silane penetrating sealer and water repellant. For concrete and masonry, Vertical/Horizontal, Traffic Grade. 5-Gallon Pail. Price/Pail. (special order; leadtime of 2-3 weeks for 1 pail orders; flammable, UPS ground only)
$845.00 $635.95
Quantity:     Add to Cart
MasterProtect H 200 Concrete/Masonry Silane Sealer (Enviroseal20) (5G)
MasterProtect H 200 (formerly Enviroseal® 20), clear, water-based, 20% silane penetrating sealer / water repellant. For stucco, concrete, brick and masonry. 5-Gallon Pail. Price/Pail.
$201.00 $145.95
Quantity:     Add to Cart
Uni-Tile Sealer LV, Epoxy-Polyamide Penetrating Primer-Sealer (2G)
UNI-TILE SEALER LV, 2-component, quick drying epoxy-polyamide solvent based penetrating primer/sealer. Dries Clear. 2-gallon kit (1G A + 1G B components). Price/Kit. (flammable; High VOC; UPS ground or truck shipment only)
$110.00 $89.95
Quantity:     Add to Cart

Shop with
Peace of Mind!