|
|
| Shopping
Cart: |
|
0
Items
In Cart |
| Total:
$0.00
|
|
 |
|
|
 |
| |
| |
| |
| |
| |
| |
| |
| |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
ACRYL 60, CONCRETE REPAIR PRIMER / BONDING AGENT (5G)
|
| ACRYL-60-5 |
$125.00 SALE $99.95 |
| (Savings: $25.05) |
|
|
| |
|
|
|
|
| |
| |
| |
PRODUCT: ACRYL 60 CONCRETE REPAIR
ADHESION PROMOTER CONCENTRATE. 5-GALLON PAIL. PRICE/PAIL. (36 pails/pallet 1700#)
DESCRIPTION:
Acryl 60 is an acrylic-polymer emulsion that is mixed with portland cement
mortars, plasters, stucco, and concrete mixes. Acryl® 60 improves the
adhesion, cohesion, tensile, compressive, and flexural strengths of these
cement-based materials. This non-yellowing, water-base material is
suitable for applications interior and exterior, above and below grade.
Acryl® 60 produces a hard, strong, and fast cure for a wide variety of
concrete-repair and cement-based coating materials.
APPLICATIONS
• Cement-based mixes to improve their adhesion,
and durability
• As gauging liquid for concrete waterproofing and concrete repair
products, such as Thoroseal® and Thorite®
• Walkways
• Ramps and structural beams, structural walls
LOCATION
• Interior or exterior
• Above or below grade
HOW TO APPLY:
Surface Preparation
1. The methods required for preparation will vary
depending on the end product to be applied and the
site and substrate conditions.
2. In all cases the surface must be clean and sound.
Remove all loose and disintegrated material. Remove
any and all traces of oil, grease, dirt, dust,
efflorescence, biological, mold or mildew, and release
or curing agents.
3. Vacuum, sweep, or blow out the areas to be
patched with clean, oil-free air.
CONCRETE/CMU/MASONRY SURFACES
Predampen the area to be patched or coated with
potable water to a saturated surface-dry (SSD)
condition. Do not leave standing water on surface.
Proper surface preparation and cleanliness are
extremely important.
OTHER SURFACES
For other surface preparation guidelines, refer to the
specific Thoro® product data guide for information.
Mixing
1. The normal ratio of Acryl 60® to clean potable
water is 1 part Acryl 60® to 3 parts water (1 to 3).
Where increased physical and chemical resistance
are required, increase the Acryl 60® content in the
mixing liquid to a 1 to 2 or 1 to 1 Acryl 60® to
water ratio (see chart above).
2. Always mechanically mix. Do not overmix or mix
at a high speed.
Application
SAND/CEMENT MORTAR
1. Thoroughly mix all cement and sand first. The
sand must be clean, free of clay, and dry.
2. Make up mixing liquid from a 1 to 3 or 1 to 2
Acryl 60® water ratio depending upon requirements.
3. Slowly add the mixing liquid to the cement/sand mixture and mix with a
slow-speed mixer for 1–2 minutes to avoid entrapping air. After preparing,
cleaning, and predampening the surface, brush apply a scrub coat (not
diluted) of the Acryl 60®-modified cement/sand. Scrub vigorously into the
surface to displace any air pockets.
4. Place the mix into the scrub-coated repair area
while the scrub coat is still wet or tacky. Place the mix and avoid
overtroweling. The trowel should be cleaned frequently, kept wet, and used
with minimal pressure.
5. Maximum time for placement should not exceed 20 minutes. Higher air and
surface temperatures will decrease working and placement time.
Curing
1. When rapid drying is expected due to high
temperatures, rapid air movement, or wind, it is
recommended that the surface be covered with
wet burlap to retain moisture.
2. For normal use, allow a 24-hour curing period.
3. For heavy wheeled traffic, allow a 4-day curing
period.
For Best Performance
• Do not use Acryl 60® modified mixes when the
ambient air or surface temperature is below
40° F (4° C) or when the temperature is
expected to fall below 40° F (4° C) within
24 hours. High relative humidity, excessive
moisture, and low temperatures will retard
the curing of Acryl 60® modified mixes.
• Do not use with air-entrained cement mixes or
with air-entraining admixtures.
• Do not overmix or aerate mixes.
• Use with proper ventilation.
• Do not use Acryl 60® as a surface-applied
external bonding agent or as a primer.
• Do not expose cement-based mixes modified
with Acryl 60® to water immersion service for a
minimum of 24 hours at 73° F (23° C).
• Not recommended for exposure to soft water or
immersion where contact with water-treatment
chemicals is present without a protective
top coat.
• Caution should be used when a highly solvent
material is being used over a base system that
contains Acryl 60®.
• Make certain the most current versions of
product data sheet and MSDS are being used;
call Customer Service (1-800-433-9517) to verify the most current version.
• Proper application is the responsibility of the user.
Technical Data Sheet
MSDS
Sheet
|
|
|
|
|