0
Items
In Cart |
TOTAL:
$0.00
|
Browse by Category
|
|
|
|
|
EPDM Bonding Adhesive LG-BA10 High-Strength, (1G)
|
EPDM-LG-BA10-1 |
$55.00 SALE $41.75 |
(Savings: $13.25) |
|
|
|
Buy
4
or more and pay $38.57 each (save $16.43)
|
|
|
|
|
|
|
|
|
|
Product:
EPDM Bonding Adhesive, LionGuard LG-BA10. High-Strength Solvent Based Neoprene Rubber Contact Cement. For EPDM Rubber Roofing. Made in USA. 1-Gallon Can. Price/Can.
Ordering Notes:
- Flammable item. UPS Ground or truck Shipment ONLY. High VOC -- Cannot ship to SCAQMD areas and other high VOC restricted areas. (shipping Class UN1133 PGII Adhesives 3).
Description:
LionGUARD Neoprene Bonding Adhesive LG-BA10 is a high-strength solvent-based contact adhesive that allows quick bonding of EPDM membrane to to wood, metal, masonry and approved roofing substrates. It may also be used as a general contact bond adhesive. Apply a thin coat to both intended surfaces and let adhesive “dry” until it is tacky to the touch. Mate both surfaces and apply mild pressure (roll with weighted roller).
COVERAGE RATES:
- About 60 square feet (56 sq m) per gallon of finished surfaces (120 sqft /gallon on each surface to be mated). Porous and irregular surfaces and substrates may require more bonding adhesive than the typical coverage rate.
CAUTIONS:
- Read the Material Safety Data Sheet for complete safety information prior to use.
- LionGUARD Neoprene Bonding Adhesive LG-BA10 is EXTREMELY FLAMMABLE - It contains solvents that are dangerous fire and explosion hazards when exposed to heat, flame or sparks. Store and use away from all sources of heat, flame or sparks. Do not smoke while applying. Do not use in a confined or unventilated area. Vapors are heavier than air and may travel along ground to a distant ignition source and flash back. A red caution label is required when shipping.
- Avoid breathing vapors. Keep container closed when not in use. Use with adequate ventilation. If inhaled, remove to fresh air. If not breathing, perform artificial respiration. If breathing is difficult, give oxygen. Call a physician immediately. During application, efforts must be made to prevent fumes from entering the building via air ventilation ducts. Do not place open containers or mix adhesive near fresh air intake units. When possible, shut down or seal off the closest units.
- If swallowed, DO NOT INDUCE VOMITING. Call a physician immediately.
- Avoid contact with eyes. Safety glasses or goggles are recommended. If splashed in eyes, immediately flush eyes with plenty of clean water for at least 15 minutes. Contact a physician immediately.
- Avoid contact with skin. Wash hands thoroughly after handling. In case of contact with skin, thoroughly wash affected area with soap and water. Note: Solvent resistant Hycron gloves are recommended when using this product to protect hands from irritating ingredients.
- Do not thin Bonding Adhesive. Thinning will affect performance. Excessively thick or gelled material should be discarded.
READ MSDS DATASHEETS BEFORE USE.
PRACTICE YOUR TECHNIQUE BEFORE USE!
More Product Information:
Questions?
Email us at sales@bestmaterials.com or
Call us at 1-800-474-7570 or 602-272-8128
You'll get a prompt reply!
similar product terms: epdm bonding adhesive, epdm adhesive, epdm rubber adhesive, neoprene adhesive, neoprene bonding adhesive, epdm rubber roofing adhesive, epdm flat roof adhesive, epdm flat roofing adhesive, roof membrane adhesive, rubber roof adhesive, rubber roofing membrane adhesive, single ply adhesive, single ply glue, single ply roofing adhesive, single ply membrane adhesive, rv rubber roof adhesive, rv roof adhesive, rv roof repair adhesive, neoprene bonding adhesive, lg-ba10
|
|
|
|
|
|